TM 11-6720-239-35
door spider (33), and secure with two rivets (11)
t. Turn slide block cover (14) over so that slide
using universal riveter tool.
block link is on bottom.
i. Mount exit cover frame assembly (24) to rear
u. Hook open end of slide block link (15) under
door spider (33) with three rivets (23) using uni-
flange in center of rear door spider assembly
versal riveter tool.
(32).
j. Mount rear door hinge (8) to rear door spi-
v. Place slide block cover (14) over slide block
der (33) and secure with three rivets (7) using
assembly (20) and edge control bar (18) so that
universal riveter tool.
holes in cover are in line with holes in slide block
assembly (20).
k. Mount rear door spider assembly (33) and
roll latch (5) on rear door (6), and secure with
w. Secure slide block cover (14) to slide block
four rivets (4).
assembly (20) with three screws (13).
l. Mount exit door assembly (3) and spring (2)
x. Raise roller support frame (32) to upright
on exit cover frame assembly (24) as follows:
position.
(1) With exit door assembly (3) facing you,
y. Turn back cover around so stenciled side of
insert spring (2) around pivot (1). Hold spring
roller support frame (32 ) faces you.
(2) with short end away from you.
(2) Using pivot stud remover and inserter
z. Insert two roller bushings (27) onto ends of
tool, press both pivot studs (1) into exit door
front roller (26).
assembly (3).
aa. Insert left end of front roller (26) in socket
(3) Hook short end of spring (2) under exit
at top of left f rent roller support (31).
door assembly (3). Long end of spring (2) is ten-
sioned against exit cover frame assembly (24).
ab. Spread right front roller support (30) until
right end of front roller (26) snaps into hole on
m. Using tweezers, hook end of spring (19)
top of left front roller support (31).
over end of slide block assembly (20) where two
screw holes are located.
ac. Turn rear door assembly so that stenciled
n. Position slide block assembly (20) so spring
side of roller support frame is facing away from
(19) is under assembly, and free end of spring is
you.
towards tab at front of roller support frame (32).
ad. Place roller bushing (27) on both ends of
o. Hook free end of spring (19) into hole in tab
rear roller (25).
at f rent of roller support frame (32), carefully
ae. Insert left end of rear roller (25) in hole at
draw slide block assembly (20) back until tracks
top of left side of roller support frame (32).
on slide block assembly (20) can be slipped under
slide plates (22), and let spring (19) pull slide
af. Press rear roller (25) forward and down
block assembly (20) forward along slide plates
until right end of rear roller (25) snaps into hole
(22). Make certain slide block assembly (20)
at top of right side of roller support frame (32).
rides freely back and forth.
p. Position edge control bar (18) so that control
316. Reassembling the
Finder Assembly
bar is away from you with tabs at end of bar
facing up, and center portion nearest you.
NOTE
q. Insert shaft (16) partially into hole in right
Before reassembly, remove all epoxy res-
arm of edge control bar (18), place one spring
idue from parts.
(17) over shaft, and drive shaft (16) through
hole in center of slide block assembly (20).
a. Using anvil and universal riveter tool, mount
r. Place second spring (17) over shaft (16),
spring post (58, 59) and two pivot studs (56, 57)
and drive shaft (16) through corresponding hole
in positions indicated.
in left arm of edge control bar (18). Center shaft
b. Insert adjusting screw (55), and six adjust-
(16) so approximately inch of shaft protrudes
ing screws (51 and 54) into holes provided in
from each arm of edge control bar (18).
housing (60) but do not tighten.
s. Hook closed edge of slide block link (15) over
flange at center of narrowest edge of slide block
c. Insert mirror (52) and mirror spring (53)
cover (14).
into channels indicated in housing (60).