TM 11-6780-225-35
(5) Install RFI filters (21) to mounting plate (22).
3-9.
Curbside Aft Compartment Repair
(6) Install RFI filter covers (18) and (20) with
screws (17) and (19).
(7) Install connector (16) with screws (14) and
a. Disassembly
nuts (15).
(8) Install circuit breakfer block (12) with screws
WARNING
(10) and nuts (11). Install modules (13). Connect all
Remove all external power to the circuit
wiring according to tag references and wiring diagram
breaker block prior to disassembly.
(9) Install panel cover (9) using screws (8).
(1) Remove screws (1) and nut (2).
(10) Install right side, bottom, and top covers (6),
(2) Remove front cover (3).
(7), and (23) using screws (4).
(3) Remove screws (4) and left side cover
(11) Install left side cover (5) using screws (4).
(5).
(12) Install front cover (3) using screws (1) and
(4) Remove screw (4) and right side, bottom,
nuts (2).
and top covers (6), (7), and (23).
(5) Remove screws (8) and panel cover (9).
3-10.
Space Heater, and Film and Print Drying
Cabinets Repair
NOTE
Remove and tag all wiring.
a. Disassembly.
(6) Remove screws (10) and nuts (11), remove
circuit breaker block (12) and modules (13).
WARNING
(7) Remove screws (14), nuts (15), and
Prior to disassembly remove power to
connector (16).
space heater.
(8) Remove screws (17) and (19) and remove
RF1 filter covers (18) and (20).
(1) Remove screws (1), washers (2), and
(9) Remove RF1 filter (21) from mounting plate
compartment cover (3).
(22).
(2) Remove screws (4) and register (5).
(10) Remove screws (24) and registers (25).
(3) Drain and disconnect all associated tubing to
(11) Remove screws, washers, and lamp
space heater (13).
assembly (26), (27), and (28).
(4) Remove screws (6), (8) and (11) and
(12) Remove screws (29) and attaching parts
attaching parts (6A), (7), (9), (10), and (12), disengage
(30), (31), and (32) and remove refrigerator (39).
electrical connector, and remove space heater (13).
(13) Snap off vent cover (33) and remove
(5) Remove screw (14) and thermostat cover
screws (34) and attaching parts (35), (36), (37), and (38).
(15).
b. Cleaning and Inspection.
(6) Remove screws (16), disconnect and tag
wires, and remove thermostat (17).
(7) Disassemble fuel line tubing and fittings (18)
(1) Inspect mechanical components for cracks,
through (40) as required. Refer to paragraph 3-13 for
dents, and damaged screw threads.
typical approach utilized in disassembly of compression
(2) Inspect electrical components for apparent
fittings.
insulation breakdown, loose connections, and possible
(8) Remove screws (44), nuts (45), and
shock hazards.
compartment cover (46).
(3) Clean all components as required using
(9) Disassemble turnscrew (47) and attaching
cleaning compound and stiff bristle brush.
parts (48), (49), and (50).
c. Assembly.
(10) Remove screws (51), attaching parts (52)
and (53), and door (54).
(11) Disassemble screws (56), washers (55),
(1) Install screws (34) with attaching parts (35),
and front plate (57).
(36), (37), and (38). Snap on vent cover (33).
(2) Install screws (29) with attaching parts (30),
(31) and (32). Install refrigerator (39).
(3) Install lamp assembly (28) with screws (26)
and (27).
(4) Install registers (25) with screws (24).
3-5
