TM 11-6720-242-35
98
Cover (MP176)
79
Belt (MIP125)
99
Screw (H83-84)
80
Flange (MP189)
100
Cover (MP203)
81
Screw (H127)
101
Screw (H85-86)
82
Flange (MP190)
102
Bracket (MP202)
83
Screw (H128)
103
Screw (H142)
84
Pin (MP672)
104
Screw (H143)
85
Pin (MP393)
105
Pin (MP811)
86
Gear (MP399)
106
Holder (MP283-290)
87
Cam (MP397)
107
Screw (H2)
88
Bearing (MP136-145)
108
Pad (MP291-298)
89
Shaft (.M:P395)
109
Prism pad (MP321-328)
90
Gear (MP392)
110
Prisn (MP299-300)
91
Pin (MP394)
111
Setscrew (MP313-320)
92
Pin (MP386)
112
Bumper (NtP305-308)
93
Gear (MP277)
113
Ring (MP309-312)
94
Bearing (MP129)
114
Cage (MP282)
95
Prism and gear assembly (MP275)
198
Housing (MP204)
96
Shim (MP363)
97
Bearing (MP154)
Figure 3-4(4)-Continued
(11) Wiring data for connector 2J3 of the
board termination's. Also, each wire must be fully
camera control.
covered with insulation tubing.
Connector
AWG
Insulation tubing
(5) Install covers (22, 23, and 24, fig. 3-8).
and is
unwire size
(6) Insert the assembled front plate (28) and
designation
AWG size
Length (in.)
interconnecting panel assembly (35) and secure is (36).
J3-A.........................No. 20 ..................18................ 3/8
J3-B.........................No. 20 ..................18................ 3/8
Secure the front panel to the chassis with four screws
J3-D ........................No. 20 ..................18................ 3/8
(27).
JI-E..........................No. 20 ..................18................ 3/8
J3-F .........................No. 20 ..................18................ 3/8
(7) Press connector (9) into contact with
J3-H ........................No. 20 ..................18................ 3/8
interconnecting panel assembly (35) and secure
J3J ..........................No. 20- .................18................ 3/8
connector (9) to bracket (29) with two screws (10) and
J3-K.........................No. 20 ..................18................ 3/8
J3-M ........................No. 20 ..................18................ 3/8
washers (11).
J3-N ........................No. 20 ..................18................ 3/8
(8) Slide aec board assembly (4), control
J3-P.........................No. 20 ..................18................ 3/8
J3-R ........................No. 20 ..................18................ 3/8
board assembly (5), and scan board assembly (6) into
J3-S.........................No. 20 ..................18................ 3/8
place in sub-classes (36). Install power supply assembly
J3-T .........................No. 20 ..................18................ 3/8
J3-U ........................No. 20 ..................18................ 3/8
*Pin letters that are not listed are spares.
Use bare bus wire in the AWG size designated.
3-30. Removal and Replacement of Handle and
a. Removal.
(1) The front panel (28) must be removed
(1) Remove the two screws (38), and washers
from chassis (36).
(39),securing handle (37) to the front panel (28).
(2) If connector (9) is still in place, remove
(2) Remove the identification plate (40) by
two screws (10) and washers (11) securing it to bracket
removing two screws (41).
support (29).
b. Replacement.
(3) Place a gasket (31, 32, or 33) on the
(1) Attach handle (37) to the front panel with
respective electrical connector and assemble front panel
two screws (38) and washers (39). Apply glyptal to the
(28) and interconnecting board assembly (35) to the
screw threads.
attaching three standoff posts. The three electrical
(2) Attach the identification plate (40) to the
connectors should extend through front panel (28) with
front panel (28) using two screws (41).
all gaskets correctly positioned.
(4) Aline the four holes in nutplate (8, 10, or
3-31. Repair and Alignment of Control Panel
12, fig. 3-12) with the mounting holes of the front panel
Components
and secure each connector with three screws (25, fig. 3-
a. Procedures for the repair and alignment of
8). There must be no tension or excessive slack in the
assemblies and parts of the control panel by di
wires between a connector and the interconnection
Change 3
3-23
